How to tune your 2020-2021 Powerstroke with an AMDP Tuner

How To Tune Your 2020-2021 Powerstroke w/ an AMDP Programmer

How To Tune Your 2022 Powerstroke w/ an AMDP Programmer - Added Power/PCM Swap + TCM Tuning Reading How To Tune Your 2020-2021 Powerstroke w/ an AMDP Programmer 4 minutes

This is a rundown on how you'll flash your 2020-2021 Powerstroke with an AMDP Programmer. 

Tools required:

  • Battery Charger
  • Windows based Laptop

Before you start:

  • Confirm all parts are present
  • Fully read the installation guide
  • Charge the batteries if you suspect they are low

ECM Instructional Video


Step 1: Locate the PCM on the Passenger side firewall and disconnect ALL 3 connectors.

Step 2: Connect the power harness to the vehicle battery (ensure correct polarity).

Step 3: Connect the Power harness to the AMDP Power Programmer, then connect the supplied PCM connector to the Passenger side PCM plug on the vehicle.

Step 4: Connect the AMDP Power Programmer to the Windows based Laptop with the previously mentioned software installed.

Step 5: Open the AutoFlasher software, select “Cable”, then Select “Connect”. If connection is successful proceed to Step 6, if it is not reinstall the USB Drivers and check the USB connections.

Step 6: Select “Service Mode”, then “Power On”. The message “Powering on module” should appear.

Step 7: Select “Service Mode”, then “Identify”. Confirm the PCM is being communicated with. If not, check power connections and repeat Step 6. The Cable S/N, ECU S/N and VIN need to be emailed to tunes@dirtydieselcustoms.com with your order number and who you ordered it through to receive the purchased tuning. To copy each number right click then Ctrl-V into the email.

Step 8: Once you have received the tunes via email, save them onto your computer. Repeat Steps 1-7 if you have disconnected from the vehicle.

Step 10: Select “Service Mode”, then “Write”, then “ECU”, select the file previously emailed to you. The tuning process will now begin. Once it has completed you can disconnect all AMDP Power Programmer connections and reconnect the factory PCM connectors.

Step 11: Ensure the vehicle starts and no DTC codes or dash messages are present. If anything is present please contact Tech support.


Transmission Tuning Video

If you purchased Transmission Tuning, please follow the steps below:


Note: 

For your truck, your TCU SN will begin with a 5 when done correctly. Once you have obtained your TCU number, please send it along with your full VIN, Cable Number, and the Order Number you purchased the tunes under.

Be sure not to use ANY of the functions on the programmer device that are not outlined in the instructions. Failure to follow instructions correctly may result i

Step 1: Connect the supplied OBD2 cable to the AMDP Powerstroke Programmer and to the vehicle’s OBD2 port. Turn the vehicle’s key to the Run/On position.

Step 2: Connect the AMDP Power Programmer to the Windows based Laptop.

Step 3: Open the AutoFlasher software, select “Cable”, then Select “Connect”. If connection is successful proceed to Step 4, if it is not reinstall the USB Drivers and check the USB connections.

Step 4: Select “OBD”, then “Identify”. Select “TCU” then “Enter”. The TCU S/N will start with a “5”. Confirm the TCM is being communicated with. If not, check power connections and repeat Step 3.

Step 5: Select “OBD”, then “Get VIN”. The Cable S/N, TCU S/N and VIN need to be emailed to tunes@dirtydieselcustoms.com with your order number and who you ordered it through to receive the purchased tuning. To copy each number right click then Ctrl-V into the email.

Step 6: Once you have received the tunes via email, save them onto your computer. Repeat Steps 1-4 if you have disconnected from the vehicle.

Step 7: Select “OBD”, then “Write”, then “TCU”, select the KAM RESET file previously emailed to you. The tuning process will now begin. Once the tuning has completed turn key off then back on.

Step 8: Select “OBD”, then “Write”, then “TCU”, select the TCM Tune file previously emailed to you. Once tuning has completed turn key off then back on, you can disconnect all AMDP Powerstroke Programmer connections.

Step 9: Start the vehicle and ensure there are no DTC codes or dash messages are present. If anything is present please contact Tech support.

You're all done! Now go enjoy your tuning!